Disinfection Product

The ozone disinfection cabin, that is, people shake their clothes for half a minute after entering the ozone disinfection cabin, and at the same time, a relative concentration of ozone is released in the closed space, which can kill germs and viruses attached to people's clothing. From this, it can be understood that ozone has a certain role in helping the current epidemic.

Ozone has strong oxidizing property, and the killing rate of ozone on various bacteria, viruses, fungi, etc. is above 99.9%, without any toxic side effects, and will not cause drug-resistant bacteria. Its bactericidal ability is 600 times that of antibiotics, 1,000 times that of alcohol, 3,000 times that of chlorine and ultraviolet rays, and thousands of times that of chemical drugs and traditional Chinese medicine.

However, ozone has a strong irritant, and ozone can irritate the mucous membrane of the human respiratory tract.

When the ozone concentration in the air reaches 0.15ppm, it can be smelled.

When it reaches 0.5-1ppm, it can cause discomfort such as dry mouth.

When it reaches 1-4ppm, it can cause cough.

When it reaches 4-10ppm, it can cause a strong cough.

People cannot be directly exposed to high concentrations of ozone for too long (the safe concentration of ozone in the air stipulated by the Ministry of Health is 0.1ppm).

When using ozone for disinfection and sterilization operations, in order to avoid harm to people in the process, it is necessary to strictly detect the concentration of ozone in a closed environment to prevent excessive ozone concentration or ozone leakage. In order to avoid the harm of ozone, the disinfection of air must be carried out in a closed space and unmanned conditions, and it can only be entered after at least 30 minutes after disinfection.

ME2-O3-16×15 ozone sensor

ME2-O3-16×15 ozone sensor

In order to prevent the ozone concentration from exceeding the standard and endangering human health, it is necessary to use an ozone sensor for ozone concentration detection. Winsen Technology ME2-O3-16×15 ozone sensor adopts electrochemical principle and has the characteristics of low power consumption, fast response speed, high measurement accuracy, good stability and repeatability. It also responds well to low concentrations of ozone. When in use, it can be combined with the digital display mode to display the ozone concentration in real time, and can also set an alarm point to realize the intelligent application of ozone detection.

Health care

RELATED PRODUCTS

Electrochemical Ozone Sensor ZE25-O3


ZE25-O3 is a general-purpose and miniaturization electrochemical Ozone detection module. It utilizes electrochemical principle to detect ozone in air which makes the module with high selectivity and stability. It is a combination of mature electrochemical detection principle and sophisticated circuit design.

Learn More

Electrochemical Ozone Sensor ME2-O3-16×15


ME2-O3-16x15 electrochemical gas sensor is fuel cell type, which utilizes the electrochemical oxidation process of O3 gas on the working electrode. The current produced in electrochemical reaction of the target gas are in direct proportion with its concentration while following Faraday law, then concentration of the gas could be get by measuring value of current.

Learn More

Electrochemical Ozone Sensor ZE14-O3


ZE14-O3 is a general-purpose and miniaturization electrochemical Ozone detection module. It utilizes electrochemical principle to detect ozone in air which makes the module with high selectivity and stability. It is a combination of mature electrochemical detection principle and sophisticated circuit design.

Learn More

Electrochemical Ozone Sensor ZE27-O3


ZE27-O3 electrochemical ozone module is a general-purpose and miniaturized module. The use of electrochemical principles to detect the ozone gas in the air, which has good selectivity and stability. The built -in temperature sensor can be compensated by temperature; it has digital output for easy use. The ZE27-O3 is a close combination of mature electrochemical detection technology with the excellent circuit design, and the universal gas module designed and manufactured.

Learn More

How to choose the right sensor for your project?

We have 17 sensor series, 200+ categories, and 300+ detection objects for gas detection. Such as CO, CO2, VOC, PM2.5, CH4, LPG and so on. In particular, we also have MEMS sensors. According to your industry application, gas principle, power consumption, accuracy, and range requirements, and we can select a specific model for you. You can also use the product filter below to choose a suitable product, or choose online serivce.

Still need help? Join the community

Related Links

Support

The first six FAQs. Use the search bar above to reveal more!

What Are the Precautions for Manual Soldering of Semiconductor Sensors?

1. Flux: rosin flux with the least chlorine; 2. Constant temperature soldering iron; 3. Temperature: 250℃; 4. Time: no more than 3 seconds.

Can Wave Soldering Be Used for Semiconductor Sensors?

Yes, but you need to pay attention to the following points: 1. Use rosin flux with the least chlorine; 2. Speed: 1-2m/min; 3. Preheating temperature: 100±20℃; 4. Soldering temperature: 250±10℃;

What is the Service Life of Mq Series Sensors?

Usually, the life span is about ten years, and the actual application is related to the use environment and method of use.
SUBMIT
Security verification
%{tishi_zhanwei}%